close
BoomkickerBoomkicker w/fittings - Sailboats 16 to 19 ft.

Product Details


Boomkicker K0400: Includes mast fitting with round luff groove slide, Boomkicker with 7/16" diameter spring rods, webbing sling to support the boom, control line from sling to mast and eyestrap with round luff groove slide.

Fits Boats:
16' to 19'.

Specifications
Imperial Metric
Initial Pin to Pin 36" 91.4 cm
Minimum Pin to Pin 26" 66 cm
Maximum Force * 150 lb 68 kg
Maximum Stroke 1 11" 28 cm
Maximum Stroke 2 ** 6" 15.3 cm
* At Maximum Pin to Pin Length.
1 Maximum stroke at initial Pin to Pin.
2 Maximum stroke at min. Pin to Pin.
** Stroke is travel when flexed. 1" of stroke equates to approximately 7" at the aft end of the boom.

Boomkickers use two coated solid fiberglass spring rods to provide the force necessary to support the boom and mainsail.

The rods are clamped into teflon anodized aluminum end pieces and attached to universal mast and boom fittings. Fittings are included along with machine screw fasteners, the proper drill and tap and hex wrench. The mast fitting includes a round slide which, used in the luff groove, avoids drilling into the mast.

Flat slides in varying widths are available from the factory. The slides can often be inserted at the sail opening above the gooseneck and slid down reassembling the fitting in position. If slides are not usable, the fitting can be attached directly to the mast using the same drill and tap provided for the boom.

The custom extruded boom track is contoured to fit both round and flat bottom booms. The track has an adjustable clevis pin to set the maximum height the Boomkicker will lift the boom. The track length forward of the pin allows the boom to move higher if needed.

Note: Uses webbing sling at boom instead of track fitting.

Part Number: K0400

Compare Chart



Boomkicker
Model
Suggested
Boat LOA
Initial
Pin to Pin
Minimum
Pin to Pin
Maximum
Force
Stroke
Initial / Minimum
K0312 14 - 16' 30" 25" 75 lbs. 11" - 6"
K0400 16 - 19' 34" 26" 150 lbs. 11" - 6"
K0500 16 - 20' 36" 26" 150 lbs. 11" - 6"
K0750 20 - 25' 36" 31" 250 lbs. 11" - 6"
K0800 25 - 27' 45" 35" 300 lbs. 15" - 6"
K1000 27 - 30' 45" 41" 400 lbs. 15" - 6"
K1250 30 - 34' 53" 43" 500 lbs. 16" - 9"
K1500 34 - 38' 53" 49" 600 lbs. 16" - 9"
* At Maximum Pin to Pin Length.
1 Maximum stroke at initial Pin to Pin.
2 Maximum stroke at min. Pin to Pin. ** Stroke is travel when flexed.
1" of stroke equates to approximately 7" at the aft end of the boom.

Installation Manual


Recommended Installation Tools:
Phillips Screwdriver, Fine Tooth Hacksaw.

1. General: To the right is a sketch of the Model K0400. Two fiberglass rods provide the force to support the boom. The boom sits in the sling between the rods and is held by a line to the gooseneck stop installed directly under the boom gooseneck. The length of the line controls teh initial height of the boom. To check the K0400 is the correct model, the minimum length is 26"(66cm) end pin to sling and the maximum weight it can support is approximately 14 lbs(6.3kgs) at the outboard end of the boom with the mainsail flaked. As shown the Boomkicker works by flexing and when straight, it is at the top of its travel.

Note that the Boomkicker does not restrict the boom from rising higher .



2. Installing Mast Bracket and Gooseneck Stop: The Boomkicker works best if the boom gooseneck is fixed in one spot on the mast. If the boom gooseneck can slide, then in the normal sailing position with the sail up, place a mark on the mast, indicating the lowest point of the gooseneck (Including any portion inside the luff groove). Then remove. Using the sail opening in the mast, first slide the mast bracket down to the vang bail, do not tighten. Next slide the top of the gooseneck stop to the mark and tighten. Reinsert the boom so against the gooseneck stop. If the boom gooseneck is fixed to the mast, the slides can be detached, slid past the gooseneck and reassembled.

3. Final Positioning: Using the main halyard, lift the aft end of the boom 6"- 8" (15cm - 20cm) above horizontal or normal sailing level . If the Boomkicker fits in the area above the vang, hold the sling around the under side of the boom and adjust the mast fitting location to make an angel between 40° and 45° with the boom. The sling line should be loose and is adjusted later. If the angle is much lower than 40°, then as the spring rods flex, they lose ability to hold the boom. Tighten the bracket in position and reattach the Boomkicker with clamp screws on top and the sling loop for the line, forward. If the Boomkicker is too long to fit in the area above the vang, or the angle is low, the spring rods can be cut down. Shorten the bottom of both rods (Use the provided hex-key to loosen rod clamp.) equal lengths of no more than 8" (20cm). A fine tooth hacksaw works best. Before tightening the rod clamp, make sure the rods are against the stops on the lower plate and Boomkicker labels are out.

4. Final Adjustments: Adjust the line between the sling and the gooseneck stop so the sling supports the boom. Since some initial stretch can be expected under load, slightly over tighten. Disconnect the halyard from the boom and press the boom down to flex the Boomkicker and test the force. Rods should flex freely upward and support the boom and mainsail without the boom sagging. Too much force will cause the boom to bow upwards. If less force is needed, optional smaller diameter rods are available either as exchange, ordered on the web or by phone.

WARRANTY: The following is made in lieu of all warranties, expressed or implied. Seller's and manufacturer only obligation shall be to replace or repair such parts of the product proved to be defective for a period of five years. User shall determine the suitability of the product for its intended use and user assumes all risk and liability whatsoever in connection therewith.

For additional information or support, contact Mauri Pro Sailing Technical Team, your Boomkicker specialist.

Click Image to Zoom
    Code: BOOK0400
    Original Price:$153.00
    Price: $114.00
    (You Save: $39.00)

    Currency:
    Quantity in Basket: None
    Quantity:
    PayPal © Site content copyright Mauri Pro Sailing, LLC. All rights reserved
    Site developed by Mauri Pro Sailing
    Mauri Logo