| |
 |
|
 |
|
|
|
How to Measure Using Loos RT Series |
 Hold the gauge with the right hand and place the rod between the two nylon spools as shown at the first picture.
With the left hand pull the lanyard and extend the spring until the hook on the nylon slider can be hooked on the rod as shown at second picture.
Release the lanyard. Read the needle position on the scale. Refer to the calibration table to obtain correct tension in the rod. The gauge can be left on the wire for "hands free" adjustment of the rod.
To assure accurate readings make sure that the slider moves freely in the frame slot and does not bind. Lubricate the slider slot frequently with silicone lubricant.
How much Tension?
Table 1 recommends an initial tension setting, but there is no simple solution since the optimum rigging tension will be a function of the boat design, the rig (masthead or fractional, one or more spreaders, etc.), and even the cut of the sails. Many skippers use insufficient tension because of a fear of "breaking something." It should be noted that on America's Cup contenders, where electronic state of the art tension instrumentation is available, the standing rigging is set as tight as is structurally feasible. |
Nitronic 50 Rod |
|
Breaking Strength |
Forestay* |
Shrouds* |
Diam,. In. |
lbs. |
kgs. |
lbs. |
kgs. |
lbs. |
kgs. |
.172 |
4700 |
2140 |
705 |
320 |
470 |
214 |
.198 |
6300 |
2860 |
950 |
430 |
630 |
290 |
.225 |
8200 |
3730 |
1230 |
560 |
820 |
380 |
.250 |
10300 |
4680 |
1550 |
700 |
1030 |
470 |
.281 |
12500 |
5680 |
1880 |
850 |
1250 |
570 |
.330 |
17500 |
7960 |
2630 |
1190 |
1750 |
800 |
.375 |
22500 |
10230 |
3380 |
1530 |
2250 |
1020 |
*Suggested initial settings.
|
|
One Design Class Racing Sailboats
It is suggested that you contact your sailmaker for the recommended initial settings for the rod rigging on your boat. For larger boats it may be prudent to check with the designer of the boat.
When no specific requirements are provided by the sailmaker, the following general comments will provide a basis for a rational procedure for tuning the rig.
Forestay Tension
Masthead Rig: On the masthead rig it's almost always advantageous to set the forestay tension as high as possible within the limits of structural strength. Generally, it's possible to use 15% of the breaking strength of the rod. Thus, a forestay tension of 1,550 lbs. is a reasonable and conservative place to start with a .250 diam. Nitronic rod.
Backstay tension would, of course, have to be adjusted to maintain a straight mast with the desired forestay tension. Since the backstay makes a greater angle to the mast, the backstay tension will be lower than the forestay tension.
Note: Roller furling can only be set by back stay tension.
Fractional Rig: In a fractional rig the forestay does not go all the way to the masthead and forestay tension cannot be directly balanced by tension in the backstay. Therefore, some mast bend is generally accepted and the mainsail is cut to fit the bend. A forestay tension of at least 15% of the rod strength is desirable. However, if this results in excessive mast bend it will be necessary to back off a bit. On some fractional rigs, diamond shrouds are used to reduce mast bend.
Order online Loos RT Series
Upper and Lower Shroud Tension
Masthead Rig: There is a simple criterion for shroud tension. The initial rigging tension should be high enough that the leeward shrouds do not go slack when sailing close-hauled in a reasonably brisk breeze. The proper value for your boat can be found by a few trial runs under sail. Once the correct tension is known, the gauge can be used to maintain the value.
For many boat designs a shroud tension of 10% to 12% of the breaking strength of the rod is adequate. Thus, for a .250 diam. Nitronic rod the upper and lower shrouds would be set to 1000 to 1200 LBS. tension. On some rigs it may be desirable to carry different tension in the uppers than lowers.
Fractional Rig: For most fractional rigs the correct shroud tension is the same as that for a masthead rig, i.e., a tension setting that will keep the leeward shrouds from going slack. However, there is one exception. On certain fractional rigs, the upper and lower shrouds lead to chain plates that are aft of the mast. The spreader is swept back. For such a rig most of the forestay tension is balanced by the upper shrouds. A shroud tension of approximately 20 % of the rod strength may be required to achieve the desired forestay tension. Never exceed 25% of the rod breaking strength. (Refer to the breaking strength chart Table 1.) |
Note: If flat spots appear on nylon spools after extended use, rotate nylon spools 45°.
Model |
Cable Diam. |
Model RT-10 |
Rod diam. .172, .198, .225, .250 |
Model RT-10M |
Rod diam. 4.4mm, 5mm, 5.7mm 6.3mm, 7.mm |
Model RT-11 |
Rod diam. .281, .330, .375 |
Model RT-11M |
Rod diam. 7.1mm, 8.4mm, 9.5mm |
Order online Loos RT Series |
Read about 90 - 91 Series | PT Series
|
Top |
|
Loos Sailboat Tension Gauges |
If you need immediate assistance finding the appropriate sailing gear, sailboat hardware or sailing equipment for your boat, please call us toll free at: 1-888-756-8883, our crew is ready to help you.
Pictures and text courtesy of Loos Sailboat Tension Gauges |
|
|
|
|
General Info |
No Sales Tax at mauriprosailing.com
Only orders shipped to Texas are charged sales tax.
Price Matching
Buy with confidence. We do our best every day to ensure that our prices are the best you can find. If within 30 days you find a better price, we’ll refund the difference as a store credit. Read more.
International Shipping
We ship to most of the countries in Europe, Caribbean South America, Asia and Oceania.
Returns & Exchanges
Customer satisfaction is our top priority and we want you to be completely satisfied with your purchase. We ensure you a quick and hassle-free return or exchange process. More.
|
|
|
